9/11 Scholars Forum

Exposing Falsehoods and Revealing Truths

HOW INDEED CAN NANOTHERMITE BE EXPLOSIVE?
& THE NANOTHERMITE CHALLENGE


T Mark Hightower, B.S., M.S., Chemical Engineering

INTRODUCTION

This paper explores the explosiveness of nanothermite.

Steven E. Jones made the error early in his research, of classifying nanothermite as an explosive in the same category as the high explosive RDX, with no published science to back up his claim. The 911 truth movement has never recovered from this error, for to this day nearly everyone in the movement refers to "explosive nanothermite," as even this clever cover for a fictitious "For Dummies" book illustrates. (1)

Examples of Jones confusing these issues are cited and commented upon. Two technical papers on nanothermite are cited to support my contention that nanothermite is not anywhere near being an explosive in the sense of a high explosive like RDX. These two papers are also cited on the issue of adding organics to nanothermites to produce gas generating nano-thermites (GGNT) and I maintain that these papers suggest that the only way to make a nanothermite truly explosive is to combine it with an explosive or other high-explosive mechanism. “It's not the “nano” that makes it explosive. It's the explosive that makes it explosive.”

Finally, I make recommendations of what those who advocate the nanothermite theory for WTC destruction can do to clarify their position and I announce The Nanothermite Challenge.

EXAMPLES OF JONES CONFUSING THERMITE AND NANO-THERMITE WITH EXPLOSIVES

Here is a two-paragraph quote from Steven Jones' first paper. (2)

“Thus, molten metal was repeatedly observed and formally reported in the rubble piles of the WTC Towers and WTC 7, metal that looked like molten steel or perhaps iron. Scientific analysis would be needed to conclusively ascertain the composition of the molten metal in detail.”

“I maintain that these observations are consistent with the use of high-temperature cutter-charges such as thermite, HMX or RDX or some combination thereof, routinely used to melt/cut/demolish steel.” (2)

Here Jones puts thermite, HMX, and RDX in the same category. But thermite is totally different than HMX and RDX. Thermite is an incendiary. It gets very hot, it produces molten iron, it can melt steel, and it can catch things on fire, but it is absolutely not an explosive. It is not even a low explosive. On the other hand, HMX and RDX are high explosives. HMX detonates at 9,100 m/s (meters per second) and RDX detonates at 8,750 m/s. He also lumps all three under the category of cutter-charges, but a cutter-charge with thermite would be totally different than a cutter-charge with a high explosive. A thermite cutter-charge would cut by melting the steel with the high-temperature molten iron it produces (an extremely low velocity and slow process compared to high explosives), whereas an RDX cutter-charge would cut by the supersonic detonation of high explosives in what is known as a shaped charge, which essentially produces a supersonic projectile of molten metal (copper is often used in shaped charges) that instantly penetrates and severs the member.

Later in the paper Jones says

“"Superthermites" use tiny particles of aluminum known as "nanoaluminum" (<120 nanometers) in order to increase their reactivity. Explosive superthermites are formed by mixing nanoaluminum powder with fine metal oxide particles such as micron-scale iron oxide dust.” (2) And further down he says “Highly exothermic reactions other than jet-fuel or office-material fires, such as thermite reactions which produce white-hot molten metal as an end product, are clearly implied by the data. In addition, the use of explosives such as HMX or RDX should be considered. "Superthermites" are also explosive as must be remembered in any in-depth investigation which considers hypotheses suggested by the available data.” (2) From page 85 of a presentation that Jones gave early in his work (3), he says “Gel explosives: Tiny aluminum particles in iron oxide, in a sol-gel: “High energy density and extremely powerful” and “can be cast to shape”. http://www.llnl.gov/str/RSimpson.html (Livermore Nat’l Lab, 2000) I have read the LLNL web page that Jones cites above (4) very carefully and I cannot find anything in it that implies that the “thermitic nanocomposite energetic material” referred to is an explosive. It refers to the result as a thermite pyrotechnic, releasing an enormous amount of heat, but it does not say that it is an explosive. In the web page another class is explained briefly, energetic nanocrystalline composites. "The Livermore team synthesized nanocrystalline composites in a silica matrix with pores containing the high explosive RDX or PETN." No mention is made here of thermite, so this wouldn't apply to Jones claiming that nanothermite is an explosive.
WTC Devastation by public domain

COMPARING NANOTHERMITE REACTION VELOCITIES TO EXPLOSIVE VELOCITIES

The explanation given for claiming that nanothermite is an explosive goes something like this. The thermite reaction is

Fe2O3 + 2 Al ---> 2 Fe + Al2O3

By making the particle sizes of the reactants smaller, down to the nanosize (approximately 30 nm to 60 nm) and mixing them well, the reaction takes place so fast that it becomes explosive. Let's look at some data from technical papers where the reaction velocity of nanothermites were measured and compare these values with the reaction velocities of explosives to see if it seems reasonable to call nanothermite an explosive.

A paper by Spitzer et al. published in the Journal of Physics and Chemistry of Solids in 2010 presents a variety of research on energetic nano-materials. (5) In one section they deal with nano-thermites made with tungsten trioxide (WO3) and aluminum nano-particles. They experimented with different particle sizes, but they highlight the mixture made with the smallest nano-particles of both WO3 and Al for its impressive performance.

“WO3/Al nano-thermites, which contain only nano-particles, have an impressive reactivity. The fireball generated by the deflagration is so hot that a slamming due to overpressure is heard. The combustion rate can reach 7.3 m/s. This value is extremely high compared to classical energetic materials.” (5)

A paper by Clapsaddle et al. published by Lawrence Livermore National Laboratory in 2005 also contains some reaction rate data for nanothermite composed of nano-particles of Fe2O3 and aluminum. (6) In Figure 2. in the paper the combustion velocity is plotted versus percent SiO2 content. The highest values were obtained at zero percent SiO2, so those are the only values I am going to cite. The nanothermite produced by a sol gel process had the highest velocity of 40.5 m/s, compared to the one produced by a simple mixing of the nano-particles with a combustion velocity of 8.8 m/s. (6)

Compare the above combustion velocities of nanothermite with the detonation velocities of high explosives HMX and RDX of 9,100 m/s and 8,750 m/s, respectively, and they are dwarfed by the velocities of the conventional high explosives. Steven Jones appears to be calling the nanothermite reaction explosive only in the sense that it is reacting much faster than regular thermite, but not in the sense that it is anywhere near as explosive as a conventional high explosive. By failing to make this distinction Jones has misled nearly the entire 911 truth movement into believing that nanothermite is a super explosive, possibly even more powerful than conventional high explosives.

From the above, it is quite clear that the “nano” in nanothermite does not make the thermite explosive anywhere near the degree of a high explosive like RDX.

In addition to saying that nano-izing thermite makes it explosive, I have heard Jones say that adding organics to nanothermite also makes it explosive. This issue is explored in the next section.

CAN ANYTHING BE DONE TO MAKE A NANOTHERMITE EXPLOSIVE?

First I would like to quote an entire two paragraph section, with its title, from the LLNL paper. (6)

“Gas generating Al-Fe2O3-SiO3/2-R (R = –(CH2)2(CF2)7CF3) nanocomposites. ”

“One limitation inherent in any thermite energetic material is the inability of the energetic material to do pressure/volume-work on an object. Thermites release energy in the form of heat and light, but are unable to move objects. Typically, work can be done by a rapidly produced gas that is released during the energetic reaction. Towards this end, the silica phase of sol-gel prepared oxidizers, in addition to modifying the burning velocities, has also been used to incorporate organic functionality that will decompose and generate gas upon ignition of the energetic composite [3-4, 7]. Phenomenological burn observations of these materials indicate that the Al-Fe2O3-SiO3/2-R nanocomposites burn very rapidly and violently, essentially to completion, with the generation of significant amounts of gas. Figure 5 shows a comparison of the ignition of an energetic nanocomposite oxidizer mixed with 2 μm aluminum metal without (left) and with (middle) organic functionalization. The still image of the energetic nanocomposite without organic functionalization exhibits rapid ignition and emission of light and heat. The still image of the energetic nanocomposite with organic functionalization also exhibits these characteristics, but it also exhibits hot particle ejection due to the production of gas upon ignition. This reaction is very exothermic and results in the production of very high temperatures, intense light, and pressure from the generation of the gaseous byproducts resulting from the decomposition of the organic moieties.”

“These materials were also mixed with nanometer aluminum. Figure 5 (right) shows a still image of the ignition of the Al-Fe2O3-SiO3/2-R nanocomposite mixed with 40 nm aluminum. This composite is much more reactive than the same oxidizing phase mixed with 2 μm aluminum metal; the burning of the composite with 40 nm aluminum occurs much too quickly to be able to observe the hot particle ejection. This observation is a good example of the importance mixing and the size scale of the reactants can have on the physical properties of the final energetic composite material. When the degree of mixing is on the nanoscale, the material is observed to react much more quickly, presumably due to the increase in mass transport rates of the reactants, as discussed above.” (6)

Note that in the title of the section quoted above, the symbol R is used to represent the organic functionality added to the nanothermite. In this case it is a 10 carbon atom straight chain functional group fully saturated, with hydrogen atoms on the first two carbon atoms of the chain and fluorine atoms on all the rest. I have not explored the precise energy level of this functional group, but I can tell by just looking at it that it will consume energy (from the thermite reaction) in order to break it down into multiple smaller molecules in order to get the expanding gases necessary to make it behave as explained. This is not an efficient way to make an explosive. I wouldn't expect the explosiveness to be anywhere near that of a conventional high explosive, and the qualitative description given in the paper certainly does not seem to support it being a true explosive, but unfortunately the paper does not give data on what its reaction rate would be. Wouldn't it be better if the organic added to the nanothermite was a molecule that, instead of consuming energy to drive its decomposition, actually produces energy as it decomposes? Such a molecule could be the RDX molecule. This leads to the quoted two-paragraph section below from the Spitzer et al. paper. (5)

“3. Gas generating nano-thermites ”

“Thermites are energetic materials, which do not release gaseous species when they decompose. However, explosives can be blended in thermites to give them blasting properties. The idea developed at ISL is to solidify explosives in porous inorganic matrixes described previously. Gas generating nano-thermites (GGNT) are prepared by mixing Cr2O3/RDX and MnO2/RDX materials with aluminium nano-particles. The combustion mechanisms of these nano-thermites were investigated by DSC and high-speed video. In the case of Cr2O3-based GGNT, the decomposition of RDX induces the expansion and the fragmentation of the oxide matrix. The resulting Cr2O3 nano-particles, which are preheated by the combustion of the explosive, react violently with aluminium nano-particles. In the case of MnO2-based GGNT, the mechanism of combustion is somewhat different because the decomposition of RDX induces the melting of oxide particles. The droplets of molten MnO2 react with aluminium nano-particles.”

“The non-confined combustion of GGNT is rather slow (1-11 cm/s) in comparison with other nano-thermites presented here. However, in a confined environment their combustion rate is expected to be significantly higher. Indeed, the thermal decomposition of GGNT produces gaseous species, which contribute to increase the pressure and the combustion rate in accordance with the Vieille’s law. The thermal decomposition of miscellaneous GGNT compositions was studied in a closed vessel equipped with a pressure gauge. The GGNT were fired with a laser beam through a quartz window. The pressure signal was recorded along time for each material (Fig. 7). The pressure released by the combustion of a GGNT is directly linked to the RDX content of the nano-composite used to elaborate it. Depending on its formulation, a GGNT can provide a pressure ranging from a few bars to nearly three thousand bars.” (5)

I am surprised by the low number given for the reaction velocity, only 1-11 cm/s. Also, it does not say what percent RDX resulted in this low velocity. Maybe it was a very low content of RDX. But the main point I want to make about the above quoted section does not depend on this velocity anyway. The key point is that you have to blend explosives (like RDX) into nanothermite to make it an explosive (“give them blasting properties”).

WHAT NANOTHERMITE ADVOCATES NEED TO DO TO CLARIFY THEIR THEORY

Steven E. Jones and other nanothermite theory advocates should be upfront and truthful about these issues, and clearly elaborate upon the factors missing from their theory that need further fleshing out. It is not good enough to just say “explosive nanothermite” over and over again without explaining exactly what is meant by the term. If they think that incendiary thermite or incendiary nanothermite or low explosive nanothermite or high explosive nanothermite were used in cutter-charges, or some combination, then they should say so. The lack of or degree of explosiveness claimed, whether incendiary, low explosive, or high explosive, is key, because the type of cutter-charge used would depend on this. Once they clarify what they mean by their use of the term “nanothermite”, then they should start describing the quantities of thermite that would have been necessary for the destruction. Only by adding these details to their theory can it be fairly evaluated against alternative theories of the destruction of the buildings of the World Trade Center for the benefit of the wider 9/11 truth community.
___________________________________

THE NANOTHERMITE CHALLENGE

Find and document peer reviewed scientific research that demonstrates that a gas generating nanothermite (GGNT) based upon iron (III) oxide (Fe2O3) and aluminum (Al), where the gas generating chemical added to the nanothermite is not itself a high explosive, can be made to be a high explosive with at least a detonation velocity of 2000 m/s. The author of this paper will donate $100 for every 1000 m/s of detonation velocity that can be documented, the donation not to exceed $1,000. For example, if a detonation velocity of 5500 m/s can be documented, then the donation amount will be $550. Only one prize will be awarded in the form of a donation to AE911Truth, and it will be awarded based upon the highest detonation velocity that can be documented. Those submitting entries grant the author the right to publish their entries. Entries must be in the form of a brief (no longer than one page) write-up, with the peer reviewed research cited, and at least scanned copies (electronic pdf files) of the cover page(s) and pages relied upon of the technical papers, if not a submittal of the entire paper(s). Entries should be sent by email to DetonationVelocity@att.net by June 20, 2011. The award will be announced and paid by July 20, 2011.

1 May 2011

ABOUT THE AUTHOR: T. Mark Hightower began his awakening in January 2004 after having stumbled upon the Serendipity web site and learning that the explosive demolition theory for WTC destruction was a more probable explanation than was the official story.

http://www.serendipity.li/

He has worked as an engineer for nearly 30 years, initially in the chemical industry, then in the space program, and currently in the environmental field. He is a member of the American Institute of Chemical Engineers (AIChE) and the American Institute of Aeronautics and Astronautics (AIAA).

His research on 9/11 is an exercise of his Constitutional rights as a private citizen and in no way represents his employer or the professional societies of which he is a member.

REFERENCES

(1) Fictitious Book Cover, “Explosives in the WTC for Dummies”

(2) Jones, Steven E., “Why Indeed Did the WTC Buildings Completely Collapse?” Journal of 911 Studies, Volume 3, September 2006

(3) Jones, Steven E., “Answers to Objections and Questions,” Department of Physics and Astronomy, Brigham Young University, 18 July 2006

(4) LLNL Web page cited by Jones – “Nanoscale Chemistry Yields Better Explosives,”

http://www.llnl.gov/str/RSimpson.html

(5) Denis Spitzer, Marc Comet, Christian Baras, Vincent Pichot, Nelly Piazzon, “Energetic nano-materials: Opportunities for enhanced performances,” Institut franco-allemand de recherches de Saint-Louis (ISL), UMR ISL/CNRS 3208, 5, rue du General Cassagnou, 68301 Saint-Louis, France,
Journal of Physics and Chemistry of Solids 71 (2010) 100–108

(6) B. J. Clapsaddle, L. Zhao, D. Prentice, M. L. Pantoya, A. E. Gash, J. H. Satcher Jr., K. J. Shea, R. L. Simpson, “Formulation and Performance of Novel Energetic Nanocomposites and Gas Generators Prepared by Sol-Gel Methods,” March 25, 2005, Presented at 36th Annual Conference of ICT, Karlsruhe, Germany, June 28, 2005 through July 1, 2005 UCRL-PROC-210871, LLNL This paper is free to download at
http://www.osti.gov/bridge/product.biblio.jsp?query_id=0&page=0...

Views: 3474

Reply to This

Replies to This Discussion

That is a great question for William Tahil. Here is the link to his on-line book:

http://www.nucleardemolition.com/files/Download/GZero_Report.pdf

If anyone knows how to contact him please let me or Jim Fetzer know. He would like to interview Tahil on his Real Deal Radio Program and I have formulated quite a number of other questions I would like to ask him.

 

A man named the Anonymous Physician also believes nukes were used. Here is a link to him:

http://wtcdemolition.blogspot.com/2008/09/did-two-nuclear-reactors-...

 

A man who calls himself the Finnish Military Expert also believes that nukes were used but he thinks it was a fusion only nuke. Here is a link to him:

http://www.saunalahti.fi/wtc2001/military.htm

 

Dr. Bill Deagle MD also believes that nukes were used based on what a patient of his reported about what he was tasked to do at the Oklahoma City Bombing site. The patient allegedly developed radiation related symptoms. He told Dr. Deagle that mini-nukes were used on the Murrah building in OK. City. Here is a link for him:

http://www.prisonplanet.com/articles/september2004/080904okcbombing...

http://www.prisonplanet.com/articles/september2004/080904okcbombing...

I just a little searching on William Tahil, B.A.

 

Did not like what I found.  There were two attempts to infect my computer with virus in searching about him.  Had to do an immediate shutdown on my computer so Word file I was collecting info on him on was lost.

 

He has no record or background that can be found.

 

He pronounces himself director of something, as I recall, as Meridian Research International, which is very similar to an established research firm named Meridian International Research, or maybe vice versa.

 

He is known on the web I guess as Mr. Peak Lithium and he has a theory about Peak Lithium.

 

He sells ebooks and apparently puts the B.A. after his name to indicate he has a Bachelor of Arts degree.

 

I am afraid Mr. Tahil is going to be another John Hutchison.

 

You have to wonder where he gets the idea that there are nuclear reactors under the Towers.  I have never heard of such an assertion before.

 

 

I'm trying to find him myself. Heard he was in the UK but don't really know yet.

 

Nowhere did I say thermite was used alone. If the perps, Bush cousins, John & Mike Cappelletti's demolition company, could get thermite into the towers, it stands to reason, they brought other explosives and THE TIMING DEVICES for the planned 911 demolitions. Cappelletti home base is in Upper Darby, PA, outside of Philadelphia, 90 miles from NYC. I started researching this in 2007. I found at that time, military grade explosives could be obtained at the Philadelphia Naval Business Center. How easy would it by for cousins of the Prez. of the U.S., who is involved in 911 up to his forehead. to get clearance for military grade thermite & other explosives at PNBC for his cousins. In addition, cousin Marvin was on the Board of Directors for security of the WTC. I also learned that OBAMA was going to shut PNBC down. Could it be to eliminate all evidence?

 

Stop and look at the evidence. I belong to a church in Manhattan where there are warped girders taken by firemen and made into a small monument from WTC implosions for the church I attend in NYC. This same church is where the mysterious Fr. Mychal Judge (who appeared as both a man with dark hair and a man with white hair in official photos) lived in St. Francis' residence.  Unless you look at the end product, how can use determine what was used. There have to be remaining chemical particles left on the steel to be looked at as evidence. Have you looked at any of the steel?

 

If and when there is a REAL INVESTIGATION by independent sources, then and only then, will anyone find answers. Pressure has to be put on CONGRESS to open a REAL INVESTIGATION. That is, unless more people will be bought off by BushCheney Obama et al. Webster Tarpley has put Richard Clarke on his list of liars. No doubt every single person who testified on 911 or about 911 has been paid to lie. You do realize the billion$ were made by insurance, real estate, stock market and death hoax FRAUD on 911.

The Osama bin Laden Myth & The Neo-Cons - History, Context & Future (Webster Tarpley)

http://www.youtube.com/watch?v=IF-3bz7rVuQ

 

I have some picture I will post as evidence for further query.

I downloaded a video from youtube and I took it apart from by frame. The video shows a faint sphere heading to the tower. This view is another view that never was aired as a broadcast. I had to make this photos big enough so that you can see the sphere. I circled 5 frames from the video: frames 23, 27, 31, 35, 39. Answer to an outside source.

Frames are out of order. I tried to do this precisely but I screwed up the order of the frames. I hope you still get the picture that a sphere was shot at the towers.

 

 

Frame 35

Frame 39

 

This is a still from the video broadcast. Notice the sphere hits the same area where the plane appears to go but at a different angle also the towers are being recorded at a different angle from where the sphere hit the tower.
 

I can barely see anything where you have it circled. Is it possible to enlarge it any further? 

Can you supply a link for the actual video?

I have more evidence of spheres hitting the towers, I will put it at the end of the thread.
These spheres no doubt were smart bombs directed at the towers. But, first you have to accept there were spheres that hit the towers, there were no planes. 1st image was too small to be a plane, possibly an unmanned drone.

"These spheres no doubt were smart bombs directed at the towers. But, first you have to accept there were spheres that hit the towers, there were no planes."

 

I have been reading and studying alternative ideas about 9-11 since 9-11-01 and this is the first I have read of this theory.

The Anonymous Physicist has a fascinating piece on the NPT that I have posted separately. It is applicable to this topic

Here is the LINK

Reply to Discussion

RSS

© 2024   Created by James H. Fetzer.   Powered by

Report an Issue  |  Terms of Service